Join the E-Club!

NEW Products

FREE Shipping

Online Catalog

Product Reviews

MLCS_all-in-one_router_plate_kit

All-In-One Router Plate Kit

3/8" thick phenolic supports any router. Two removable rings give three different bit openings (3-7/8", 2-5/8", 1-3/16"). Note: 1-3/16" opening is designed to hold Porter-Cable® style guide bushings. The steel starting guide pin allows routing curved work. The plate is approximately 9" x 12" with pre-drilled table mounting holes. Includes magnets and adjusting screws for securing and leveling plate. Also includes concentric rings on bottom of plate for easy alignment when installing router.

All-In-One Router Plate Instructions (PDF)

All-In-One Router Plate Kit

#9338 .................... $34.95

Replacement Rings & Guide Pin
#9329 ................................SALE $10.95
All-In-One Router Plate Kit
MLCS_all-in-one_router_plate_kit

Aluminum Router Plate

Our 1/4" thick aluminum router table insert will support the heaviest of routers, without plate sag. The plate is about 9" x 12" and includes leveling screws and magnets to secure the plate in the table. Includes three separate insert rings with attaching screws which provide opening sizes (3-1/4", 1-7/16", 1-3/16" for template guides and a blank insert ring to create your own size). The steel starter pin is for routing curved pieces. Pre-marked mounting hole indentations provided for most popular routers. (The plate is not pre-drilled).

 Aluminum Router Plate Instructions(PDF)

Aluminum Router Plate
#9334 ............................................. $65.95

Replacement Rings & Guide Pin
#9330 ....................................SALE $10.95
Aluminum Router Plate
MLCS_installation_template_and_bushing_kit

Installation Template & Bushing Kit

The router plate must fit perfectly, and this kit makes it easy! Includes a masonite routing template, guide bushing (fits Porter-Cable® style baseplate opening) and instructions. Requires 1/2" straight bit. (Items #5477 or #7777).

#9331 ..........................................SALE $20.95
Installation Template & Bushing Kit
supertuff_router_mounts

SuperTuff Router Mounts

Replace your router's plastic base with long lasting "SUPERTUFF" material. These clear, shatter resistant squares can be drilled, cut or routed as needed to make your router table inserts, safety shields, router fixtures or projects. Measures 11+" square and is available in 1/4" or 3/8" thickness.
1/4" Super Tuff Router Mount
#9095 Reg. $17.95........................SALE $14.95

3/8" Super Tuff Router Mount
#9097 Reg. $21.95........................SALE $18.95
univeral_centering_alignment_pin

Universal Centering Alignment Pin
This handy set-up tool is designed to fit both 1/4" and 1/2" router collets, and center the baseplate to the collet. It’s vital for inlay work, pattern router, and using any precision fence system. It will also indicate the exact center of any bit cut, which is important when locating grooves and dadoes. The centering /alignment pin can be used to check run-out on drill press, mill and lathe chucks.

Universal Centering Alignment Pin
 #9054 Reg. $14.00..........................SALE $5.95


MLCS Router Collet Extension
MLCS_router_collet_extension

For 1/2" collet routers! Give your router bits an additional 2-1/4" (for #9465 or 2" for #9473) when you extend them through the router table top with our router collet extension. Eliminate the dangerous temptation of withdrawing the shank from the collet in order to raise the bit and to "provide the full depth of cut." The router collet extension makes it possible to use all diameters of 1/2" and 1/4" shank bits safely. Place the router collet extension shank in the 1/2" router collet and the router bit shank in the extension collet and tighten both. Wrenches and instructions included.

Router Collet Instructions(PDF)
ROUTER COLLET EXTENSION for 1/4" and 1/2" shank bits
#9465 For 1/2" shank bits. Reg. $42.90 $29.95
#9473 For 1/4" shank bits. Reg. $42.90 $29.95

Wrench Sets for previously purchased Router Collet Extensions are now available for both 1/4" and 1/2" shank.
#9466 1/2" Shank Wrench Set.....SALE $7.95
#9474 1/4" Shank Wrench Set.....SALE $7.95
WEB SPECIAL!
Get BOTH 1/4" and 1/2" Router Collet Extensions
Plus a 3 Piece Wrench Set
#1721 2 ROUTER COLLETS and
3 WRENCHES
Regular Price $59.95		 $49.95

MLCS_brass_router_height_set-up_kit

Brass Router Height Set-Up Kits
Perfect for router, shaper and table saw set-up. Soft metal Brass Bars won't splinter or chip your router bit or saw blade if they accidentally hit the cutters.

BRASS MULTI SIZE SET-UP KIT
2-3/8" bars allow accurate depth adjustments in 6 sizes (1/16", 1/8", 3/16", 1/4", 3/8", 1/2"). Attached to keychain.
#9718 list $20.00........................ONLY $15.95

SQUARE 4" LONG BAR KIT
Allows depth adjustments in five sizes: (1/8", 3/16", 1/4", 3/8", 1/2"). 4" Long Bars fit across router opening.
#9717 Square Bar Kit...................ONLY $24.95
MLCS_router_table_power_switch

Router Table Power Switch
The Router Table Power Switch allows safe and convenient on/off control of 120V AC routers or tools. Mounts quickly and prevents reaching under the table to turn off your router (WHICH GREATLY INCREASES SAFETY!). Just plug your router into the Power Switch and plug the Power Switch into the wall outlet. Removable lock even prevents unauthorized use. 67" power cord. Maximum 15 amps. 9079
#9079 List. $41.50............... $24.95


No rating yet... Be the first to rate this product!

all customer reviews and ratings

No rating yet... Be the first to rate this product!
MLCS_router_table_power_switch

Safety "Router Table" Power Switch
This convenient, mechanical push button switch features a large paddle "STOP", to allow you to quickly shut off power to your 120VAC machinery. Placing the switch where you can use your hip or knee to bump it into the "off" position gives you the freedom to never take your hands off the workpiece to turn off the machine. Just plug your router into the Safety Power Switch router cord and plug the Safety Power Switch power cord into the wall outlet. Surface mounts quickly and easily. Max. 20 amps.
#9078 ................................ONLY $29.95


No rating yet... Be the first to rate this product!

all customer reviews and ratings

No rating yet... Be the first to rate this product!
MLCS_router_table_power_switch

Safety "Motor" Power Switch
Now you can replace or upgrade the power switches on your woodworking machinery. Exactly the same switch as above but needs to be hardwired to the router motor and to power cord. Surface mounts. Max. 20 amps. Will work with 110 or 220 volt motors.
#9072 ................................ONLY $21.95


Rated:

Review this product...

all customer reviews and ratings

Average Customer Rating: (1 reviews)
Add your own review for this product

'Ol WC from Michigan (5/5), Oct 9, 2009

By Wes Crawford ( Mi US)

I have installed the hardwired version on my table saw/router table extension. Many use this paddle switch mounted on the side of the table. Mine is also on the side, but faces to the front on an angle bracket at exactly the right height for thigh operation. This allows me to keep both hands on the workpiece at all times. This is a 2 pole switch, and I use the second set of poles on the switch to operate my shop vac. I installed a double duplex receptacle set-up adjacent to the switch which is handy for the vac and other tools. The switched receptacle is for the vac and is controlled by an adjustable "off delay" cube relay mounted in the magnetic starter for my table saw that allows the vac to run a preset length of time after the router is turned off to clear the hose.

When I'm done with the router, I just plug the vac in "next door" in the other non-switched receptacle to use with other operations.

The switch has worked flawlessly, and I highly recommend it. In fact, I wish it was available in a momentary contact version to use with the table saw. I could use this maintained contact version, but would have to give up the benefit of no auto restart after a power outage. Unfortunately, where I live, these are all too common.


Offered for the convenience and safety of all my fellow wood butchers,

Wes Crawford


Add your own review for this product


Miter T-Fence
MLCS_miter_t-fence

Miter Gauge not included.

Miter T-Fence (PDF)

Add the ULTIMATE fence and stop system to your miter gauge! Miter-T-Fence will insure dead-accurate miter cuts and provide support close to the blade to eliminate tear-out. The adjustable, extruded aluminum fence increases the face of your miter gauge to 2-5/16" high x 22 long. The built-in extension bar increases the stop capacity to 36". The included nylon stop adjusts along the full length of the fence, and locks tight for perfect repetitive cuts. Miter Gauge not included.
Miter T-Fence
#9467 Reg $64.95...............................SALE $54.95

BUY BOTH & SAVE $10!
Miter Gauge and Miter T-Fence Set
Includes #9458 and #9467
#9457 .......................$79.90


Miter Gauge
MLCS_miter_t-fence

WEB SPECIAL! SAVE $5. Our Miter Gauge features a full 60º travel both left and right with adjustable positive stops at both 90º and 45º. The 3/4" x 3/8" x 18" miter bar securely locks into a miter T-slot or will fit standard miter slots.
Miter Gauge
 #1725 ......................................SALE $29.95

BUY BOTH & SAVE $10!
Miter Gauge and Miter T-Fence Set
Includes #9458 and #9467
#9457 .......................$79.90


Clamping Miter Gauge

Useful and accurate when making crosscuts or routing end grain on table saws. Squeezing the pistol grip engages a downward pressure clamp, securing your stock firmly in place. Fits any standard 3/4" x 3/8" miter slot. The positive adjustable stops at 90º and 45º, left and right, are useful for both left and right tilt table saws. Includes adjustable stop block, great for repetitive length cuts. 4" Maximum stock thickness. Bar extends to 12".
 Clamping Miter Gauge
 #9456 ......................................SALE $44.95
BUY BOTH & SAVE $10!
Clamping Miter Gauge and Miter T-Fence Set
Includes #9456 and #9467
#9453 .......................$89.90



T-Track Hold Downs
T-Track Hold Downs

Convenient metal T-track clamps work on any t-track that accepts a 1/4" or 5/16" hex head bolt. The T-shaped base and 1" round brass hold down will secure stock from 1/4" to 2" thick against your table, or use on jigs that have a T-track. Use on a drill press table to secure the work piece. Can also be used on a drill press or router table fence to mount stop blocks onto the T-track in the fence face. Sold as a pair.
#9441 Reg. $34.95 ...................SALE $29.95


Miter T-Track & T-Bar
MLCS_miter_t-track_&_t-bar

WEB SPECIAL! SAVE $5 for #1702! Works with standard 3/4" x 3/8" miter gauges with or without a T-slot. Our track is great for shop built router tables that are not equipped to handle a miter gauge. You can add a miter or sliding fixture to anything that can be routed out to fit the Miter T-Track work bench, table saw extensions, drill press tables, and band saw tables. The miter T-bar slides into the miter track or miter slot in your table saw. The T-bar can be used to make sliding jigs and other fixtures throughout the shop. Add a lock down knob by drilling and taping the T-bar, there is no end to the possibilities. Use #7785 (1-1/4" Straight bit) to make the groove for the Miter T-Track. T-Track length may vary up to 1/8". 

Miter T-Track and T-Bar
A 32" #9871Miter T-Track ...........................SALE $16.95
A 48" #1702Miter T-Track ...........................SALE $19.95
B 32" #9872Miter T-Bar ...............................SALE $16.95
32" MITER T-TRACK & BAR SET
Includes One Of Each... BUY BOTH AND SAVE!
#9873....................................$28.95


Combo T-Track / Miter T-Track

 MLCS_combo_t-track_miter_t-track

Our combo T-Track/Miter T-Track lets you use your miter gauge or tenoning jig, plus T-Track accessories on your router table, band saw table or table saw extension. The T-Track accepts any accessory that uses a 1/4" hex head bolt, such as featherboards, stop blocks or hold downs. The Miter track accepts a standard 3/4" x 3/8" bar or sliding T-Bar. 32" length may vary up to 1/8".  

32" Combo T-Track/Miter T-Track
#9859.....................................................SALE $24.95


Miter T-Track Accessory Kit

 MLCS_miter_t-track_accessory_kit

Create custom jigs and fixtures with our Miter T-Track slot locking kit. Lock all types of featherboards onto table saws, router tables and band saws. The T-bar will fit any 3/4" x 3/8" miter T-slot groove. Instructions are included for attaching to a featherboard or making a circle cutter for your router. Includes:

2 pcs Aluminum T-nuts (1-stop, 1-pivot)
2 pcs 1/4"Flat Head Screws
2 pcs 1/4" Triangle thru Knobs\
1 pc 1/4" Set Screw (1/4" hex)
2 pcs 1/4" Washers
1 pc 1/8" Allen Key
1 pc plastic Spacer
1 pc 4x20mm self-tapping Screw

Miter T-Track Accessory Kit
#9870Miter T-Track & T-Bar Accessory Kit.............$9.95