NEW! Improved OnPoint demonstration Video.
Making Beaded Panels with the OnPoint How-To Video.



Dual-Light Laser Guided Router Plate



Pre-Drilled with Built-In LED Lights!

LASER GUIDED FOR PINPOINT ACCURACY!
X marks the spot! Never miss your mark again when plunge routing.

WOOD Magazine HOT NEW TOOL 2008 Review

AN MLCS EXCLUSIVE! Now with the added LED lights you can light up your work surface and see clearly when trying to follow any lines or patterns. Save time, money, and eliminate waste with pinpoint accuracy. Great for any handheld plunge router applications. Off set UNIVERSAL router plate allows for total control of your router. The large clear base and knob/handle will eliminate the tipping problem that can often occur when edge routing, while allowing you to clearly and precisely see the project that you are working on.
• All electronics self contained. No wiring or plug needed.
• Made of heavy duty, tough clear plastic.
• Increase the speed and accuracy of repetitive plunge routing applications.
• Quick and easy to mount any router. Can be drilled to fit any router.
• 2 AA Batteries included

Pre-Drilled for the following routers:
Porter Cable- 690 series, 7529, 8529
Bosch - any base with a 3 hole pattern, spaced 4" on center
DeWalt 616/618 Series, 621/625
Milwaukee 5615/5616/5619 Series
Fein FT-1800 • Elu 177
Sears - Most models

OnPoint Laser Router Plate Instructions (PDF)

OnPoint Laser Router Plate General Instructions HERE.
Instructions For Perfectly Spaced Dado Cuts, etc. HERE.
 ONPOINT Dual-Light Laser Guided Router Plate
ITEM #9098 .,,.. SPECIAL! $49.95
spacer

No rating yet... Be the first to rate this product!
OnPoint Laser Guided Router Plate with LED lights
Click on small images below to see
enlarged detail.
spacer

OnPoint Laser Detail
Laser light detail

OnPoint LED Detail
LED Light detail

all customer reviews and ratings

No rating yet... Be the first to rate this product!


Demonstration video of the Improved Laser Guided Router Plate with LED lights.


This detailed How-To video demonstrates how to make Bead Board Panels using the
Point Cutting Round Over Router bits and our Laser Guided Router Plate.

On-Point Universal Laser Guided Router Plate #9098 General Instructions
Install the 2 AA Batteries into the Switch/Battery Box
Power switch has 3 positions:
1) Lasers On
2) Power Off
3) LED On

The plate can be drilled to fit almost any router. Follow the instructions bellow if your router does not fit a pre-drilled whole pattern. The On Point has been pre-drilled for the following routers:

Porter Cable- 690 series, 7529, 8529
Bosch 1617/1618 D Handle Base Only
DeWalt 616/618 Series, 621/625
Milwaukee 5615/5616/5619 Series
Fein FT-1800
Elu 177
Sears 315.175 040, 315.175 050, 315.175 070

See hole pattern diagram at right.

On-Point Universal Laser Guided Router Plate General Mounting Instructions –
For routers not listed above.
1. Remove the sub-base from your router.
2. Put a V Groove, or any pointed/small diameter router bit into your router.
3. Place your router on top of the Laser Plate and line up the point/center of the router bit with the exact center of the “X” of the laser guides.
4. Be sure the mounting screw holes in your router base do not overlap the laser guides or wiring in the Laser Plate. If it does simply rotate your router until the holes are clear of the laser guides and wiring.
5. Very carefully mark the mounting screw whole pattern on the Laser Plate.
6. Drill the proper size hole for your mounting screws completely through the Laser Plate.
7. From the bottom side of the Laser Plate counter sink each hole so that the screw head is below the surface of the Laser Plate. This will ensure that the screw heads will not mar your work or interfere in any way.
8. Mount your router to the Laser Plate.
9. Turn off Laser Plate when not in use. This will extend the life of the batteries and lasers.

Tips-
Use heavy duty double face tape to mount your router to the Laser Plate as a temporary solution.
Holes can be counter bored up to 3/8” for shorter screws.
The router’s sub base can be used as a pattern for marking mounting holes.



Hole Pattern

#1 fits:
Porter Cable 690, 7529, 8529
Bosch 1617/1618 D Handle Base Only
DeWalt 616, 618
Milwaukee 5615, 5616, 5619

#2 fits:
DeWalt 621, 625
Elu 177
Fein FT-1800

#3 fits:
Sears 315.175.040
Sears 315.175.050
Sears 315.175.070

Warning:
Always wear proper safety protection and follow the safety instructions of your router properly.

Danger - Avoid direct eye exposure from the lasers.
Class 111A Laser Product
Max output <5 mW

Back to OnPoint Laser Router Plate - Click here.

Using the On-Point Universal Laser Guided Router Plate to make perfectly spaced cuts
Easily set up your straight edge guide using the On-Point's laser as your reference point. Perfect for cutting dado slots in furniture construction or making general decorative cuts in any project.

Set-up and Use:
1. On your work piece, mark the centerline of your slot or groove with a pen, pencil or marking gauge.
2. Position the On-Point router base over the centerline drawn in step 1 at either end of the line. Turn on the laser and center the laser's cross hair directly over the point at the end of the line. Place your straight edge guide so that it is flush against the On-Point router base. (see fig. A and additional tip below).

fig. A
3. Move the On-Point router base to the opposite end of the line. Keeping the router base oriented the same way as it was in step 2, again place your straight edge guide so that it is flush against the On-Point router base. (see fig. B and additional tip below)

fig. B
4. Lock your straight edge guide in place and rout your groove.

Additional tip:
If you are routing stopped grooves instead of through grooves, when you have the router set on the ends of your lines, clamp a stop block at the edge of the router base. Then when the On-Point router base contacts the stop block(s), you have cut the full length of your stopped groove (see fig. C).


fig. C ( Stop Block Shown Clamped to Work Piece)
 
Back to OnPoint Laser Router Plate - Click here