Katana® raised panel, Mitered Door Frame, Matched Rail & Stile Set, Stacked Ogee Rail and Stile, Undercutter Router Bits

Raised Panel Router Bits

2 flute, carbide tipped with totally enclosed ball bearing guides. Katana offers four exquisite profiles: a graceful cove curve, classic ogee, the simple and steep Shaker bevel, and the 18º bevel. See Review of 18º bevel router bit from the Fine Woodworking "Knots" discussion board.

Katana router bits feature rounded shoulders, a European Anti-Kickback design which forces shallower initial cut, resulting in smoother entry into stock, which therefore drastically reduces the chance of kickback.

Item #	Bit Type	Large Dia.	Cut Hght.	Cut Depth	Shank	Price	Order
#18677	45° Shaker	2-3/4"	5/8"	1-1/8"	1/2"	$55
#18686	18° Bevel	3"	5/8"	1-1/4"	1/2"	$55
#18688	Cove	3"	5/8"	1-1/4"	1/2"	$55
#18689	Ogee	3"	5/8"	1-1/4"	1/2"	$55

Raised Panel Router Bits with Undercutter

katana_raised_panel_ogee_with_undercutter_router_bit

2 flute, carbide tipped with totally enclosed ball bearing guides. Allows you to produce flush panels, add a radius to the back side of panels for a decorative appearance or reduce the exposed upper panel profile. Cuts the front and back of the panel with one bit.

Item #	Bit Type	Large Dia.	Cut Hght.	Cut Depth	Shank	Price	Order
#18696	18° Bevel	3-1/8"	1-1/8"	1-1/4"	1/2"	$74
#18697	Cove	3-1/8"	1-1/8"	1-1/4"	1/2"	$74
#18698	Ogee	3-1/8"	1-1/8"	1-1/4"	1/2"	$74
#18699	45° Shaker	2-1/2"	1-1/8"	15/16"	1/2"	$74

Mitered Door Frame Router Bit

See How-To Video! 2 flute, carbide tipped with totally enclosed ball bearing guide. This versatile router bit creates dramatic rail and stile doors, picture or mirror frames, chair rails, crown moldings or other decorative trim. Combine with any raised panel router bit to create highly decorative raised panel doors that until now have only been available through high end cabinet shops. Use a 1/4" slot cutter to create the slot for the raised panel or a rabbeting bit to make glass panel doors, mirrors or picture frames. The stock is mitered at 45º, glued and biscuit joined to create a sturdy secure joint. This bit is designed to work with 2-13/16" wide stock and a recommended thickness of at least 3/4". Use in a 1/2" table mounted router. For cup hinges, use 1" thick stock (minimum). 1/2" shank.

Item #	Large Dia.	Cut Hght.	Shank	Price	Order
#18781	1-1/2"	2-1/2"	1/2"	$79.95

How-To Mitered Door Frame Video

Matched Rail & Stile Router Bit Set

2 flute, carbide tipped with totally enclosed ball bearing guides. These rail and stile cutters are a matched two piece male and female set so the joint fits perfectly. Use with 3/4" stock. For FREE INSTRUCTIONS, click here. 1/2" shank.

Item #	Bit Type	Large Dia.	Cut Hght.	Cut Depth	Shank	Price	Order
#18847	Ogee	1-5/8"	3/4"	3/8"	1/2"	$84.95
#18843	Round Over	1-5/8"	3/4"	3/8"	1/2"	$84.95
#18837	Shaker	1-5/8"	3/4"	3/8"	1/2"	$84.95

**Set-Up Blocks for Katana^® Matched Rail and Stile bits**
Item	Profile	Use for bit	Price	c
#9741	Ogee	#18847	$10.95
#9745	Round Over	#18843	$10.95
#9748	Shaker	#18837	$10.95

Stacked Ogee Rail & Stile Router Bits

2 flute, carbide tipped with totally enclosed ball bearing guides. Make perfect rails and stiles easily and quickly with just one bit. Just lower or raise the bit to cut the rail or stile respectively. That’s it! No need to reassemble cutters, remove the bit from your router, or change your table set-up. Because the bit is comprised of three cutters, you can add shims in-between to achieve a perfectly milled joint. For FREE INSTRUCTIONS, click here. 1/2" shank.

Katana’s™ cutters are made from premium micro-grain carbide, which has a longer cutting life and less edge breakdown. Super small granulates in carbide composition allow more resharpenings.

Item #	Bit Type	Large Dia.	Cut Hght.	Cut Depth	Shank	Price	Order
#18871	Ogee	1-5/8"	1-3/8"	3/8"	1/2"	$62

**Set-Up Block for Katana^® Stacked Ogee Rail and Stile bit**
Item	Profile	Use for bit	Price	c
#9741	Ogee	#18871	$10.95

Undercutter Router Bits

3 flute, carbide tipped with totally enclosed ball bearing guides. Our two undercutters are designed to relieve the back of a 3/4" raised panel with a 1/8" radius or 45° bevel shaped rabbet cut. This reduces the exposed upper panel profile and will let the panel sit flush with the door frame. 1/2" shank.

Item #	Profile	Large Dia.	Cut Hght.	Cut Depth	Shank	Price	Order
#18679	1/8" Radius	2-1/8"	1/4"	5/8"	1/2"	$30
#18678	45° Bevel	2-1/8"	1/4"	5/8"	1/2"	$30

Router Bits and Woodworking Products