Katana® Flush Trim Router Bits
|
|
 |
||||||||||||||||||||||||||||||||||
|
2 flute, carbide tipped with totally enclosed ball bearing guides. For use in trimming laminates and pattern/template routing. 1/4" and 1/2" shank.
|
Solid Carbide Spiral Flush Trim Router Bits |
 |
|||||||||||||||||||||||||||||||||||||||
| 2 flute solid carbide spiral bits have two ball bearing guides. Use when chip-out is a concern with plywood, melamine, laminate or wood. Downcut bit is for hand held router applications. As seen and recommended in WOOD® Magazine (#158). 1/4" and 1/2" shank. | ||||||||||||||||||||||||||||||||||||||||
|
Katana® Pattern/Flush Trim Router Bits |
 |
||||||||||||||||||||||||||||||||||
| 2 flute, carbide tipped with totally enclosed ball bearing guides. The top mounted bearing is ideal for template routing. In addition to template routing these bits are convenient for flush trimming in many applications where a bottom mounted bearing is not practical. Exactly trims workpiece to pattern. No sanding is required. 1/4" and 1/2" shank. | |||||||||||||||||||||||||||||||||||
|
Katana® Shear Angle Flush Trim Router Bits
|
|
 |
||||||||||||||||
|
2 flute, carbide tipped with totally enclosed ball bearing guides. The shear angle cutting flutes produce a smoother cut than the traditional straight fluted bits. Instead of chopping at the wood fibers at a 90˚ angle, the shear angle design allows for a smoother shear angle, slicing cut. Eliminates tear-out problems when routing end or cross grain on hard woods. 1/4" and 1/2" shank.
|
Flush Trim/Pattern Top & Bottom Bearing Bits
|
|
 |
||||||||||||||||||||||
|
NEW! See our Flush Trim Top & Bottom Bearing bit How-To Video! Two bits in one! You have the option of mounting your template above or below your workpiece. You can trim laminate on either side of your substrate without having to change router bits or turn over your workpiece. Just adjust your router bit height before making your second pass. All bits are 2 flute, carbide tipped with two totally enclosed ball bearing guides. 1/4" and 1/2" shank.
|
|
Watch a demonstration video of the Katana Flush Trim/Pattern Top & Bottom Bearing Bits
|
|
|
Katana® Flush Trim/Pattern Bit Kits
|
|
 |
||||||||||||||||
|
Remove precise amounts of material from the edge of doors or very large panels, or whenever size makes it difficult to use a router table. By varying the bottom bearing diameter, you can accurately remove 1/16" or 1/8" in two passes. Kits are available for stock up to 1-3/8" thick, or 2" thick. Kit includes 3/4" Top & Bottom Bearing Flush Trim/Pattern Bits with two 3/4" OD bearings, two additional bearings (5/8" and 1/2" OD), and a hex key. (When using the bit, for the first pass adjust the bottom bearing to run at the bottom of your stock, removing the designated amount from the top of the stock. For the second pass, readjust the bit height to allow the top bearing to run along the previously cut top of your stock, completing the trimming operation).
|
Laminate Trimming Bits with Euro Square Bearing |
 |
|||||||||||||||||||
|
Do the same work in less time! Specially designed 2 flute carbide tipped laminate trimming bit #15517 includes the Euro™ Square Teflon bearing. The bearing slides on clean laminate edges and will not scratch your work piece. Glue will not stick to the bearing. The bit cuts a slight bevel for a clean cut and no filling is required. The 3/4" diameter size is perfect for larger routers and router tables. Patent pending.
Will not scratch Corian™ and other solid surface man-made materials. Item #15513 is also specially designed for laminate trimming and includes a round bearing. 1/4" shank. |
||||||||||||||||||||
|
|
|
Questions? Call Toll Free: 1-800-533-9298 
