          |
-
Straight Router Bits
- Reviews
Two flute, single flute and European
1 or 2 flute, carbide tipped router bits. Will plane edges, cut grooves, rabbets, slots, and dadoes. Also used for mortising and carving, as well as other applications where a flat bottom is required. Items #5490-#5493, #7790-#7795 are designed for European metric size plywoods. See chart below for the undersize equivalency. Item #7794 is a 5/8" oversized bit for recessing shelf standards. Item #5468 is designed to be used for Sears dovetail jig. Item #7782 is an oversize cutter for Melamine.
Use #5479/#7779 for cutting dadoes for T-Tracks.
Use #7785 for cutting a groove for Miter T-Track.
| Single Flute Straight | ||||||
|---|---|---|---|---|---|---|
| Item | Large Diam. |
Cutting Length |
Shank Size |
Shank Length |
Price | |
| #5465 | 1/16" | 1/4" | 1/4" | 1-1/4" | $9.95 |  |
| #5466 | 1/8" | 1/2" | 1/4" | 1-1/4" | $9.95 | |
| #5467 | 3/16" | 1/2" | 1/4" | 1-1/4" | $9.95 | |
| European Two Flute Straight | |||||||
|---|---|---|---|---|---|---|---|
| Item | Triple Wing | Large Diam. |
Cutting Length |
Shank Size |
Use for Undersize |
Price | |
| #5490 | — | 5.2mm (13/64") |
1/2" | 1/4" | 1/4" | $7.95 | |
| #7790 | — | 5.2mm (13/64") |
1/2" | 1/2" | 1/4" | $8.95 | |
| #7793 | — | 12.3mm (31/64") |
3/4" | 1/2" | 1/2" | $9.95 | |
| #7795 | — | 18.2mm (23/32") |
3/4" | 1/2" | 3/4" | $11.95 | |
all customer reviews and ratings
-
Shear Angle Straight Router Bits
- Reviews
The cutter angle slices smoothly
into stock!
NEW BITS! 2 flute, carbide tipped. The shear angle cutting flutes produces a smoother cut than traditional straight fluted bits. Instead of chopping at the wood fibers at a 90º angle, the shear angle design produces smoother shear angle, slicing cuts. Use this router bit to eliminate tear-out problems from routing end or cross grain on very hard woods.
| Shear Angle Straight Router Bits | ||||||
|---|---|---|---|---|---|---|
| Item | Large Diam. |
Cutting Length |
Shank Size |
 |
||
| #5489 | 3/8" | 3/4" | 1/4" | $9.95 | |
|
| #5483 | 1/2" | 3/4" | 1/4" | $9.95 | |
|
| #7796 | NEW! | 5.2mm | 3/4" | 1/2" | $9.95 | |
| #7788 | 1/4" | 3/4" | 1/2" | $9.95 | |
|
| #7789 | 3/8" | 1" | 1/2" | $9.95 | |
|
| #7797 | NEW! | 12.3mm | 1" | 1/2" | $9.95 | |
| #7792 | 1/2" | 1" | 1/2" | $9.95 | |
|
| #7783 | 1/2" | 1-1/2" | 1/2" | $12.95 | |
|
| #7798 | NEW! | 18.2mm | 1" | 1/2" | $12.95 | |
| #7791 | NEW! | 3/4" | 1" | 1/2" | $12.95 | |
| #7799 | NEW! | 1" | 1" | 1/2" | $15.95 | |
all customer reviews and ratings
Average Customer Rating: (2 reviews)
Add your own review for this product
By Tom Cowdrey (Aylett VA US)
Love this shear angle bit. I cuts hard walnut better than the straight bits and stays sharp longer. Highly recommend.
By Jim Schneider (Jacksonville NC US)
I needed a router bit that could cut to 1 1/2” but I have a small Bosch router that uses a 1/4” shanks. I’ve looked high and low where I am in NC to no avail. I started looking online and MLCS was either first or second on the google search. These guys were one of two places I found that have what I needed. I ordered the straight 1/4” shank with an 1 1/2” cutting length and it arrived in 4 days. I gotta tell you, I’m very pleased with the bit. I used it to cut through oak, walnut and poplar so far. I cut a round 48” table using oak and the bit never quit. I also expected it to begin dulling about the time I finished with the oak. Boy was I wrong!! It cut into walnut just as smooth as the oak. I HIGHLY recommend anyone looking for a quality product to give MLCS a try for any of your woodworking needs.
Every time I use my router, I cut a 1/4” or less at a time and take your time. Let the bit cut and don’t force it. You can’t forget that or you’ll end up thinking it’s the product’s fault and not your own. Remember the basics and you can’t go wrong.
Thank you guys for your service.
Jim Schneider